SupportMotoAirbag vestAirbag system compatibility with outer layers (Jackets, Suits, etc…)
Back

Airbag system compatibility with outer layers (Jackets, Suits, etc…)

WEARING THE AIRBAG SYSTEM WITH MOTORCYCLE JACKETS

Compatible under certain conditions

A = Jacket width at chest level
B = Chest size (without the airbag vest)

● Step 1 – Measure A
● Step 2 – Calculate 2 x A
● Step 3 – Substract B from the result of Step 2 to get the measurement M

    ➜ If M is lower than 13cm / 5 in, then your equipment is  incompatible
    ➜ If M is higher or equal to 13cm / 5 in, then your equipment is compatible

CAUTION: Measurements are made with the equipment that will be worn when using the airbag product (sweater, additional protection, removable liners, etc…)

CAUTION: In order to get the most accurate measurements, ensure to stretch the jacket at chest level.

🛈 Motorcycle gear (textiles or leathers) are elastic and deform (with use, sunlight, the movements you make, etc.) allowing the airbag to find the space it needs to deploy at optimal pressure and thus absorb the energy of the impact.

🛈 The In&motion airbag system can therefore be worn under any motorcycle jacket as long as you follow the procedure above to ensure there is enough room for the airbag to deploy.

WEARING OF THE AIRBAG SYSTEM UNDER 1-PIECE RACING SUITS

Compatible under certain conditions

Compatible suits tested by In&motion are listed below:

 9 Ixon suits : Vortex 2Vortex LadyFalconVendettaVendetta EvoJackalLegendary, Vortex 3Vortex 3 Lady (size guide specific to this product) (Ixon size guide)

2 Furygan suits : Full ride, Overtake (Furygan size guide)

2 Held suits : Slade II, Expite (Held size guide)

 1 Klim suit : (road use only) : Hardanger(Klim size guide)

3 Gimoto suits : Aragon Air, LTD Air, Mugello Air (Gimoto size guide)

 1 ONE-X suit : X-RACE

 In addition, you should know that the leather suits from our partner brand RST directly integrate the In&motion airbag system.

CAUTION: Using the In&motion airbag system under an incompatible suit could cause the system to malfunction in the event of an incident.

CAUTION: For your safety, if your suit already has a backpad, remember to remove it when wearing the airbag. Wearing a back protector in addition to the one already in your airbag product could compromise the proper deployment of the system.

CAUTION: The In&motion system is compatible as long as you choose a compatible race suit that is adapted to your body type and follows the manufacturer’s sizing guide.

WEARING THE AIRBAG SYSTEM WITH ZIPPED JACKETS AND PANTS

Compatible under certain conditions

 Motorcycle jacket must be compatible (see above).

Pant size must follow the manufacturer’s sizing guide.

For leather jacket and pant sets, the pants must have an additional stretch area in the crotch.

 In the case of a set where the jacket is a product with integrated airbag, the set is compatible if the pants are of the same brand.

 One of the 2 parts of the zipper, either on the jacket side or on the pants side, must be mounted on a flexible area (stretch fabric or mechanical flex

● of at least 3 cm / 1.25 in for a textile product
● of at least 5 cm / 2 in  for a leather product

WEARING THE AIRBAG SYSTEM WITH PRODUCTS IN THE FORM OF ZIP UP ZIPPABLE LINERS

Compatible under certain conditions

In the case where the In&motion airbag system is in the form of a zip -up liner (Held eVest Clip-In et Furygan Airbag System), it is compatible with the range of clothing defined by the brand in which the liner can be zipped.

You did not find what you were looking for?
We suggest you visit our website designed especially for your location to get the right content and product availability.

In&motion

Votre navigateur est obsolète

Pour profiter du site,
merci de mettre à jour votre navigateur